Главная/
Каталог/
M/
MAKITA/
Инструменты/
Бензоинструмент и техника/
Резаки бензиновые (бензорезы)/
EK 8100/
EK 8100
EK 8100
| П-п | Название |
|---|---|
| 001 | TANK CAP COMPLETE |
| 002 | 0 RING 29.5 |
| 003 | SUCTION HEAD |
| 005 | TA PPING SCREW 5.5X45 |
| 006 | WASHER 5.8X26X2 |
| 007 | VIBRATION DAMPER |
| 008 | AXLE FOR VIBRATION DAMPER |
| 009 | FUEL TANK CPL. BLUE |
| 10 | SINTER INSERT |
| 11 | VALVE |
| 12 | FUEL LINE |
| 13 | SCREW PLUG |
| 14 | PIN 3 |
| 15 | PIN 3 |
| 16 | SAFETY LEVER |
| 17 | SPRING |
| 18 | THROTTLE LEVER |
| 19 | INDICATION LABEL |
| 20 | THROTTLE LINKAGE |
| 21 | RETAINER FOR DAMPER BLACK |
| 22 | VIBRATION DAMPER |
| 23 | AXLE FOR VIBRATION DAMPER |
| 24 | H.L. SOCKET HEAD BOLT M5X40 |
| 25 | SIDE SUPPORT MAKITA |
| 26 | MAKITA LOGO LABEL |
| 27 | TAPPING SCREW TORX 5.5X20 |
| 28 | AXLE FOR V IBRATION DAMPER |
| 29 | VIBRATION DAMPER |
| 30 | WAS HER 5.8X26X2 |
| 31 | TAPPING SCREW 5.5X45 |
| 32 | TAPPING SCREW 5.5X45 |
| 33 | WASHER |
| 34 | VIBRATION DAMPER |
| 35 | EK8100 NA ME PLATE |
| 36 | WRAP AROUND HANDLE CPL |
| 37 | FOOT, MACHINED |
| 38 | TA PPING SCREW 5.5X45 |
| 39 | PLUG |
| 41 | COVER CPL. BLACK PRE-FILTER |
| 42 | THUMB SCREW M6X 15 |
| 43 | FILTER COVER COMPLETE |
| 44 | CAUTION LABEL |
| 044-1 | CAUTION LABEL |
| 45 | PRE-FILTER |
| 53 | H.L. SOCKET HEAD BOLT M5X50 |
| 54 | HOOD CPL. BLACK |
| 55 | PACKING RING |
| 56 | CAUTION LABE L |
| 57 | DEKO COVER |
| 58 | A IR FILTER |
| 59 | INNER FILTER |
| 60 | H.L. SOCKET HEAD BOLT M5X20 |
| 61 | H.L. SOCKET HEAD BOLT M5X12 |
| 62 | SPRING WASHER 5 |
| 63 | MUFFLER CPL. |
| 67 | MUFFLER GASKET |
| 68 | COOLING PLATE |
| 69 | INTAKE MANIFOLD CPL. |
| 70 | TUBE BLACK RED |
| 71 | ANGULAR NIPPLE |
| 72 | INTAKE HOSE |
| 73 | SPR ING CLAMP |
| 74 | GUIDE RING |
| 75 | CHOKE SHAFT |
| 76 | CHOKE LINKAGE |
| 77 | H.L. SOCKET HEAD BOLT M4X55 |
| 78 | INSULATION TUBE |
| 79 | GASKET |
| 80 | CARBURETOR |
| 81 | HOSE CLAMP |
| 82 | TUBE 3-120 |
| 83 | RUBBER GROMMET |
| 84 | NIPPLE |
| 85 | MAKITA LOGO LABEL |
| 86 | STARTING DEV ICE CPL. BLUE |
| 87 | SPRING WASHER 5 |
| 88 | STARTER GRIP |
| 89 | H.L. SOCKET HEAD BOLT M5X20 |
| 90 | STARTER HOUSING BLUE |
| 91 | REWIND SPRING COMPLETE |
| 92 | CABLE DRUM COMPLETE |
| 93 | A IR GUIDE PLATE |
| 94 | RETAINING RING A14X 1V |
| 95 | HEXAGONA L NUT M8 |
| 96 | SPRING WASHER 8 |
| 97 | FLYWHEEL D=120 CPL |
| 98 | BEARING BOLT |
| 99 | STARTER-RATCHET |
| 100 | TORSION SPR ING 13 |
| 101 | CABLE W ITH PLUG |
| 103 | CONTACT SPRING |
| 104 | H.L. SOCKET HEAD BOLT M5X20 |
| 105 | ISOLATING WASHER |
| 106 | IGNITION COIL CDIM 120-15 |
| 107 | PLUG CAP |
| 108 | TERMINAL SPRING |
| 109 | SPARK PLUG |
| 111 | HOOD |
| 112 | H.L. SOCKET HEAD BOLT M5X 15 |
| 113 | H.L. SOCKET HEAD BOLT M5X30 |
| 114 | RADIA L RING |
| 115 | SQUARE NUT M5 |
| 116 | RUBBER SHEET |
| 117 | CRANKCASE MS CPL. |
| 118 | CLAMPING PIN |
| 119 | CRANK CASE GASKET |
| 120 | BALL BEARING 6202 |
| 121 | TORX SOCKET HEAD BOLT M5X23 |
| 122 | DECOMPRESSION VALV E |
| 123-1 | CY LINDER ASS\'Y |
| 123 | CY LINDER PISTON SET |
| 125 | CIRCLIP 12 |
| 126 | PISTON PIN |
| 127 | PISTON 52 |
| 128 | PISTON RING 52 |
| 129 | CIRCLIP 12 |
| 130 | GASKET |
| 131 | PISTON PIN BEAR ING 12X16X 13 |
| 132 | WOODRUFF-K EY 3X3,7 |
| 133 | CRANKSHAFT CPL. |
| 134 | BALL BEARING 6202 |
| 135 | CRANKCASE CS CPL |
| 136 | RADIA L RING |
| 137 | SNAP RING A 16 |
| 138 | STOP RING |
| 139 | GUIDE DISK |
| 140 | CLUTCH DRUM CPL. |
| 141 | NEEDLE ROLLER BEAR ING 15X2 1X 16 |
| 142 | FLAT WASHER 12 |
| 143 | CLUTCH, CPL |
| 144 | TENSION SPR ING |
| 145 | V-BELT |
| 146 | CLUTCH COVER |
| 147 | H.L. SOCKET HEAD BOLT M5X14 |
| 150 | HEX. BOLT M8X25 |
| 151 | FLANGE 102 |
| 152 | AXLE |
| 153 | FLANGE 102 |
| 154 | SPACER, 8MM |
| 155 | PRESSURE RING |
| 156 | SLIDING DISC |
| 157 | RUBBER RING(INNER) |
| 158 | RUBBER RING(OUTER) |
| 159 | SLIDING DISC |
| 160 | IMPACT PLATE |
| 161 | CAUTION LABEL |
| 161-1 | CAUT ION LABEL |
| 162 | HOOD |
| 162-1 | HOOD COMPLETE |
| 163 | GR IP |
| 164 | -H.L.SOCKET HEAD BOLT M5X16 |
| 165 | CUTIING DEVICE |
| 167 | RETAINING RING 40X1,75 |
| 168 | BALL BEAR ING 6203LLU |
| 169 | RETAINING RING 40X1,75 |
| 170 | SPACER, 8MM |
| 171 | BALL BEARING 6203LLU |
| 172 | 0-RING 9 |
| 173 | STOP BOLT CPL. |
| 174 | HEX. BOLT M8 |
| 175 | COMPRESSION SPRING 8 |
| 176 | H.L.COLLAR BOLT M6 |
| 177 | BELT PULLEY |
| 178 | HEX. BOLT M8X25 |
| 180 | PLATE |
| 181 | SQUARE NUT M6 |
| 182 | COMPRESSION SPRING 6 |
| 183 | BELT COVER |
| 184 | TENSIONING SCREW M6 |
| 185 | COLLARED HEX NUT M8 |
| 186 | PARTS FOR WAT ER ATICHMENT KIT |
| 187 | CAPPING NUT |
| 188 | HOLLOW SCREW, BORED |
| 189 | HOLLOW SCREW, BORED |
| 190 | CAPPING NUT |
| 191 | H.L.SOCKET HEAD BOLT M6X14 |
| 193 | FOOT |
| 194 | H.L. SOCKET HEAD BOLT M5X16 |
| 195 | H.L. TA PPING SCREW 5 12 |
| D10 | INC. 125-129 |
| D10 | INC. 125-129 |
| D10 | INC. 120 |
| D10 | INC. 2 |
| D10 | INC. 10-19 |
| D10 | INC. 26 |
| D10 | INC. 43.45 |
| D10 | INC. 42,44 |
| D10 | INC. 55-57 |
| D10 | INC. 70,72,73 |
| D10 | INC. 87-94 |
| D10 | INC. 98-100 |
| A0 1 | TOOL KIT |
| C10 | TORXWRENCH |
| C20 | UNIVERSA L WRENCH 13-19 |
| C30 | SCREWDR IVER |
| C40 | TOOL BAG |
| C50 | ADAPTER 20 - 25,4 |
| A02 | COUPLING SLEEVE |
| D10 | INC. 161 |
| E01 | CLEAR LABEL |
| D10 | INC. 172 |
| D10 | INC. 144 |
| D10 | INC. 141 |
| D10 | INC. 134 |
Наша компания предоставляет вам возможность самостоятельно найти схему вашего изделия и сделать по ней заказ нужной вам запчасти, которую мы постараемся найти у поставщиков и привезти её к вам Мы пришлем вам предложение с указанием сроков и цены. Цена включает в себя доставку до нашего склада в Санкт-Петербурге (15% от стоимости изделия).
Доставка до вашего адреса от нашего склада выставляется отдельным счетом. Срок бесплатного хранения на нашем складе 2 недели от даты уведомления о поступлении заказа на склад, дальше хранение платное - 1% в день от стоимости заказа.